This page does everything for you, step by step: it makes the new firmware from Line 6's own file,
shows you how to install it, and turns your .nam captures into files the HX Effects can play. It works in
your browser on a Mac or a Windows PC. Nothing is installed and nothing is uploaded anywhere.
Unofficial and experimental. This isn't made or supported by Line 6. Installing modified
firmware is at your own risk and may void your warranty. If anything goes wrong, Rescue (at the bottom)
puts the normal firmware back, from this page or with Line 6 Updater; your presets and IRs survive it.
Good to know before you start
HX Edit only works for loading files. You can still use it to import IRs and NAM captures (the
.wav files from step 4) and to back up. It can't show or edit NAM, the amps or the new effects: build and
edit presets that use them on the HX Effects itself.
Too many heavy blocks in one preset can freeze or restart the unit. NAM, the amps and some of the
effects use a lot of the processor. Add heavy blocks one at a time, and save your presets often so
nothing is lost if the unit restarts.
This is still experimental, and problems can happen. The unit may still freeze now and then, and you
may hear crackles or dropouts, especially when it's connected to a computer and recording into a DAW. Most of
this comes from running close to the limit of the unit's processor. If it happens, take a heavy block out of
the preset; if the unit freezes, turn it off and on.
1
Get ready
About 10 minutes. Tick these off as you go.
Keep that Line 6 file somewhere safe: it's also what you use to go back to the normal firmware.
2
Make your firmware
Choose what you want, then drop Line 6's file here. The page gives you a new file to install.
Open this page from its web address.
You opened it as a file on your computer, and browsers don't let a file page do this step. Use the page's web
address instead.
Takes 10–40 seconds. You can change your mind later: make another
file here and install it the same way. Every choice also shows sharps (A#) instead of flats (Bb) in the tuner.
3
Install it
Two ways: straight from this page, or with Line 6 Updater. Both write the same file.
Option A: install from this page
Needs Chrome or Edge (Safari and Firefox can't reach USB devices). Works on a Mac; on
Windows, Line 6's driver may keep the browser from seeing the unit, so use option B there if it isn't found.
Make your firmware in step 2 first.
Quit HX Edit and Line 6 Updater: they hold the USB connection.
Connect the HX Effects with USB, turn it on, and click Install on my HX Effects. Pick the
HX Effects in the browser's list. The unit restarts twice during the install; when the page asks,
click Continue and pick it again (it may show up as "LPC" or an unknown device).
Wait about two minutes, until the page says it's done. Don't unplug or switch off the HX Effects
meanwhile.
Technical details
Option B: install with Line 6 Updater
Click Download your firmware in step 2.
Quit HX Edit if it's open. Updater can't reach the HX Effects while HX Edit is using it.
Connect the HX Effects to the computer with USB and turn it on.
Open Line 6 Updater, sign in, and click your HX Effects.
Click Choose File (not the normal update) and pick the downloaded file,
HX_Effects_v3.80.0_NAM_Amps_Effects.hxf.
Let it finish, about two minutes. Don't unplug or switch off the HX Effects while it updates. It
restarts by itself. If Updater says something went wrong, run it again with the same file.
Check it worked
Add a block on the HX Effects and open Distortion › Mono: you'll see NAM A2
Lite. With the amps, there's also a new Distortion › Amps group.
Stuck on the splash screen, or it says "Boot Failure"? Don't worry: follow Rescue at the bottom of this page.
4
Add your NAM captures
The HX Effects plays NAM captures from its User IR slots. First turn each .nam into a .wav, then
send it to a slot, from this page or with HX Edit.
No captures yet
Converted captures appear here. Only the A2 Lite size works (on ToneHunt and
similar sites, look for "A2 Lite" or a file that offers several sizes).
Option A: send them to the HX Effects from this page
Needs Chrome or Edge. Quit HX Edit and Line 6 Updater first, and on the HX Effects pick a
preset without a NAM block in it. The captures go into User IR slots one after another, starting at the slot
you choose; NAM A2 Lite's Model knob reaches slots 1 to 21.
Slot
Name
Technical details
Option B: load them with HX Edit
Click Download all above (or Download on each capture).
Open HX Edit with the HX Effects connected. First pick a preset without a NAM block in it.
Open the Impulses list and drag a .wav onto a slot from 1 to 21. Note its number,
for example 5.
The .wav isn't a sound you can hear: it carries the capture's numbers. Don't use it in a Cab or IR
block; it's only for the NAM A2 Lite block.
5
Play NAM A2 Lite
On the HX Effects itself (HX Edit can't edit the new blocks). In every choice from step 2.
Add a block and pick Distortion › Mono › NAM A2 Lite.
Turn Model to the slot number from step 4. You hear the capture.
Knob
What it does
Model
Which capture plays: the User IR slot (1–21) that holds it.
Input
Level into the capture, −20 to +20 dB. 5.0 is unchanged.
BassMid TreblePresence
Tone, ±12 dB. 5.0 is flat.
Ch Vol
Output level. 5.0 is unchanged.
Polarity
Normal or Inverted.
Up to two NAM blocks in a preset, each with its own capture.
Presets remember the slot number, not the capture, so keep each capture in its slot.
Most NAM captures are of an amp without its cabinet: put an IR or cab block after NAM A2 Lite.
Click, a metronome that follows tap tempo, is under Delay › Mono in every choice too.
6
Play the HX amps
If you chose NAM + Amps or NAM + Amps + Effects in step 2.
Add a block and open Distortion › Amps: all 111 of the HX Stomp's amps, 94 guitar and
17 bass, with the Stomp's own knobs.
The preamps (the amps without their power amp section) are under EQ › Preamps.
There are no cabs: put an IR block after the amp, with a cab IR in a User IR slot.
Up to three amps and preamps in a preset, together.
Amps are heavy blocks: next to NAM and the heavier effects, the unit may refuse one more.
7
Play the new effects
If you chose NAM + Amps + Effects in step 2. Each one is in the list of the stock block it replaces (the
stereo version of that block stays).
Effect
Where, and what it is
Drum Chapel
Delay › Mono. A basic drum machine that follows tap
tempo: pick a groove and a kit (seven, one with sampled acoustic drums). The footswitch starts and stops it.
Bolt, Rocket!
Distortion › Mono. Bit crusher with 16 shaping curves.
Garrrry Tank
Distortion › Mono. Square-wave octave fuzz.
Quality Polis
Distortion › Legacy. A square-wave synth that follows
what you play.
Bam Crusher
Distortion › Mono. Sequenced bit crusher with stutters.
Doom Chug
Distortion › Mono. A low drone generator; try it into Bolt,
Rocket!, Quality Polis, Garrrry Tank or Bam Crusher.
Pure Whitey
Distortion › Mono. A glitchy sampler with eight modes.
Greasy Strangler
Pitch/Synth › Mono. A drone that follows your notes and
holds the last one.
Bethblahem
Pitch/Synth › Mono. A low theremin-style synth.
Puggy Puncher
Delay › Mono. A slot-machine glitch on every step,
in time with tap tempo.
Several of these use a lot of the processor. Add them one at a time; the unit refuses a block when a preset is
full. Save often.
?
Questions
Why do I need Line 6's file?
The firmware belongs to Line 6, so this project can't hand it out. The page takes your copy and adds the new
parts to it on your computer.
Is anything uploaded?
No. Everything happens inside this browser tab. Your firmware and captures never leave your computer.
How do I know the new file is right?
The page checks your Line 6 file's fingerprint (MD5) first, and the finished file's fingerprint at the end.
It only says Verified when the result is exactly, byte for byte, the file the project tested on a real
HX Effects.
It says it isn't the right firmware file.
It must be HX Effects version 3.80.0, exactly as Line 6 made it. Older or newer versions don't work.
Don't pick a file made here (it ends in _NAM_Amps_Effects.hxf).
A renamed file is fine: only what's inside counts.
My capture says "No 3-channel A2 Lite model inside".
NAM captures come in several sizes, and the HX Effects can only run the A2 Lite size. Look for the A2 Lite
version of the capture.
!
Rescue: put Line 6's firmware back
If the HX Effects won't start, stops on the splash screen or says "Boot Failure", or you just want the normal
firmware back. Your presets, IRs and settings stay.
Don't worry: the new firmware never touches the part of the unit that starts it up, so it can always be
rescued.
1. Start the HX Effects in update mode
Quit HX Edit and Line 6 Updater. Connect the HX Effects to the computer with USB.
Turn it off. Hold the right arrow (>) button while you turn it on, and keep holding for about three
seconds. It starts in update mode (the screen stays dark or shows an update message).
If it still starts up normally, that's fine too: the
rescue works from there as well.
2. Reinstall Line 6's firmware from this page
In Chrome or Edge: drop Line 6's own file here
(HX_Effects_v3.80.0_0xd97239907.hxf, the one from step 1; you can download it again from
line6.com/software), then click
Rescue my HX Effects and pick it in the browser's list.
Drop Line 6's file above first.
Technical details
Or: with Line 6 Updater
If this page can't find the unit (for example on Windows, where Line 6's driver may hide it from the browser):
start it in update mode as above, open Line 6 Updater, click the HX Effects, click Choose File and
pick Line 6's own file. Let it finish, then turn the unit off and on.
Still stuck after both? Turn the unit off for a minute, try another USB cable and port, and run the
rescue again. A failed or interrupted rescue can always be run again.